Bennett-marine EIC5000 Electronic Indicator Control Manuale Utente Scaricare il pdf (Pagina 1)

(EIC5000)

ELECTRONIC INDICATOR CONTROL

INSTALLATION AND OPERATION

INSTRUCTIONS

IMPORTANT - SPECIAL REQUIREMENTS:

System is voltage specic. Please make sure •

you have a 12 or 24 volt EIC5000 depending

on your requirements.

(SEE FIGURE 1)•

Special sensor coils are required if:

- Actuator stroke is more than 2 ½" OR

- Less than 1" of piston shaft is exposed

when the actuator is fully retracted OR

- Actuator has external hydraulic connection

System will not work when actuator stroke is 1" or less•

If installing in an M80 or M120 Sport Tab kit, your actuator will have three molded rings as •

shown in Figure 1. Cut the metal rod to 6 ⁄" as indicated by score mark (see enclosed

instruction sheet for cutting the rod).

BEFORE BEGINNING INSTALLATION:

READ INSTRUCTIONS COMPLETELY

MAKE SURE BATTERY POWER IS DISCONNECTED

TEST SYSTEM BEFORE PUTTING THE BOAT BACK IN THE WATER

FIGURE 1

7/16", 1/2" & 9/16" Wrench Teon Tape Marine Grade Sealant

1/8", 3/16", 5/16" & 3/4" Drill Bit Wire Stripper Vise Grips

2" Hole Saw Electric Drill Wire Cutter

REQUIRED TOOLS

KEEP THIS MANUAL WITH BOAT OWNER’S INFORMATION

Bennett Marine, Inc.

550JimMoranBlvd•DeereldBeach,FL33442

Phone:954.427.1400•Fax:954.480.2897

Web: www.BennettTrimTabs.com

External Hydraulic

Tubing Connection

Three Rings

(cut rod only)

Less Than 1"

When Fully

Retracted

}

Less Than 1" or More

Than 2 ½" Total Stroke

}

1 2 3 4 5 6 7 8 9

Sommario

Pagina 1 - INSTRUCTIONS

(EIC5000)ELECTRONIC INDICATOR CONTROL INSTALLATION AND OPERATION INSTRUCTIONSIMPORTANT - SPECIAL REQUIREMENTS: System is voltage specic. Please make

Pagina 2

IMPORTANT: Check Special Requirements noted on the front cover of this manual before beginning installation. If you are installing a preassembled actu

Pagina 3 - EIC Display

EIC Installation Overviewnipple into actuator upper hinge. Tighten nipple hand tight. Then, with vise grips, tighten two full turns … NO MORE. Cover

Pagina 4

Step 10 - Mounting the EIC Relay Module The Module is best located in a dry location close to the Hydraulic Power Unit. Use the mounting hardware to

Pagina 5 - Diagnostic Information

Calibration and OperationCalibration – NOTE: If you have Upper and Lower Helm EIC Displays installed, calibration must be done at the Lower Helm EIC

Pagina 6 - Troubleshooting

Electro-Hydraulic System Information EIC Relay Module Fuse: 12 volt system uses 20 amp in-line fuse on positive, 24 volt uses 10 amp. EIC Display Fuse

Pagina 7 - Upper Hinge Templates

2 1/8"3/16"2.832.832 1/8"2"EIC Display TemplateØ 3/4"Ø 5/16"Ø 3/16"Ø 3/16"Ø 3/16"REVISIONSZONEREV.DESCRIP

Pagina 8 - BEGINNING INSTALLATION

EIC5000 Electronic Indicator Control – Upper HelmINSTALLATION AND OPERATION INSTRUCTIONSREAD INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATIONSte

Pagina 9 - INSTALLATION DIAGRAM

EIC5000 Electronic Indicator Control – Upper HelmINSTALLATION DIAGRAM

Commenti su questo manuale

Nessun commento

Bennett-marine EIC5000 Electronic Indicator Control Manuale Utente Pagina 1

Navigare online o scaricare Manuale Utente per Hardware Bennett-marine EIC5000 Electronic Indicator Control. Bennett Marine EIC5000 Electronic Indicator Control User Manual Manuale Utente

Sommario

Commenti su questo manuale

Bennett-marine EIC5000 Electronic Indicator Control Manuale Utente Pagina 1

Navigare online o scaricare Manuale Utente per Hardware Bennett-marine EIC5000 Electronic Indicator Control. Bennett Marine EIC5000 Electronic Indicator Control User Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Hardware Bennett-marine EIC5000 Electronic Indicator Control